800 Fast Acting Grip ‘N Strip®

Removes multiple layers of lead-based oils, latex paints, varnishes, stains and other finishes in one application on wood and masonry, and is an ideal paint remover for overhangs and ceilings.
Paste like consistency that clings to vertical and overhang surfaces, allowing penetration of more layers of paint mil thickness.
Requires neutralizing.
This product must be shipped freight as it is considered hazardousCOVERAGE: 25 to 50 sq. ft./gal., depending on layers to be removed.

Category: Strip & Remove

Description

800 Fast Acting Grip ‘N Strip® peel and scrape off paste paint remover is an effective way to remove multiple layers of lead-based oils, latex paints, varnishes, stains and other finishes in one application on wood, masonry, plastered walls or metals. 800 Fast Acting Grip ‘N Strip® paint remover is designed to produce its own outer skin, making it easy to use requiring no paper over lay. The 800 Fast Acting Grip ‘N Strip® formula is an ideal paint remover for intricate carvings, moldings, pillars, capitals, overhangs, ceilings and where normal removers do not adequately penetrate.

With its paste like consistency applied uniformly, 800 Fast Acting Grip ‘N Strip® penetrates more layers of paint mil thickness and reduces water rinse normally needed to dissolve stripper residue. 800 Fast Acting Grip ‘N Strip® clings to vertical and overhang surfaces preventing sagging, dripping and sliding. 800 Fast Acting Grip ‘N Strip® is available in a wide range of formulas. This variety is to protect surfaces against excess damage that can be caused by strong caustics.

800 Fast Acting Grip ‘N Strip® is a caustic paint remover that requires neutralization (See 800 Neutralizer label and product specification sheet.) 800 Fast Acting Grip ‘N Strip® is not recommended for use on veneered or plywood surfaces, or when preparing wood cabinets or other interior woodwork for a stained and varnished finish. (Acceptable only if surface is just to be painted). 800 Fast Acting Grip ‘N Strip® will etch lexan, and other common protective plastic, as well as aluminum. Protect these surfaces. 800 Fast Acting Grip ‘N Strip® should be handled with extreme caution.

Additional information

PRECAUTIONS:	Read the entire material safety data sheet and product label for a more thorough evaluation of hazards. Fully protect all adjacent surfaces, including vegetation and aluminum from coming in direct contact with 800 Fast Acting Grip ‘N Strip®. When stripping interiors, lay plastic sheeting on floor then cover plastic with stacks of newspaper or cardboard to absorb scraped residue.
TECHNICAL DATA:	Color/Form: Tan paste.
COVERAGE:	25 to 50 sq. ft. per gallon, depending on layers of paint to strip.
PACKAGING:	One and five gallon containers.
SURFACE PREPARATION:	Prepare a surface free from dirt and oil. It is not necessary to remove loose, peeling or flaking paint. This creates pockets down to the original masonry or wood surface which is generally more absorbing than the painted surface. A test area should be performed prior to beginning overall project to determine optimum dwell time for the product and the number of applications necessary to completely remove all traces of finish from the surface. User shall determine the suitability of the product for its intended use and assumes all risk and liability whatsoever in connection therewith. Follow all local, state, or federal disposal regulations when using this product.
APPLICATION:	1. Apply 800 Fast Acting Grip ‘N Strip® approximately 1/8-1/4 inch thick with a trowel, or synthetic brush. 2. Allow 800 Fast Acting Grip ‘N Strip® to remain on surface until all paint is dissolved. 1 to 24 hours may be required. 800 Fast Acting Grip ‘N Strip® will penetrate an average of one (1) layer of paint per hour. CAUTION: Allowing 800 Fast Acting Grip ‘N Strip® to remain on wood for extended periods of time, may result in raised grain. 3. Covering 800 Fast Acting Grip ‘N Strip® with plastic sheeting may increase product effectiveness. Although it is not required, test to determine if covering is beneficial. Product efficiency is slower in cooler temperatures.
REMOVAL:	1. Scrape and peel off formed membrane. Rinse with water to completely remove 800 Fast Acting Grip ‘N Strip® residue. Beware of wind drift onto adjacent surfaces. 2. When using 800 Fast Acting Grip ‘N Strip®, neutralize the surface with ABRP 800 Neutralizer. Rinse 800 Neutralizer. (Read label for all instructions).
STORAGE:	800 Fast Acting Grip ‘N Strip® should be stored in the containers in which they are purchased. Avoid storing 800 Fast Acting Grip ‘N Strip® near acids or mixing with acid. Failure to do so could create violent heat reactions.
DISPOSAL:	Contact local, state and/or federal agencies to ensure compliance with regulations governing the disposal of this product along with coatings and finishes that may be removed when using this product.
FINE PRINT:	Read about warranties, notices, and technical services here: https://www.abrp.com/wp-content/uploads/2017/05/SpecSheet_GripNStrip.pdf